Фильтр :
Стандарт и/или проект | Этап | ТК |
---|---|---|
Geometrical Product Specifications (GPS) — Dimensional measuring equipment — Design and metrological characteristics of mechanical dial gauges
|
90.93 | ISO/TC 213 |
Dial gauges reading in 0.01 mm, 0.001 in and 0.0001 in
|
95.99 | ISO/TC 213 |
Geometrical Product Specifications (GPS) — Dimensional measuring equipment — Design and metrological characteristics of mechanical dial gauges — Technical Corrigendum 1
|
60.60 | ISO/TC 213 |
Geometrical Product Specifications (GPS) — Dimensional measuring equipment — Design and metrological characteristics of mechanical dial gauges — Technical Corrigendum 2
|
60.60 | ISO/TC 213 |
ISO general purpose metric screw threads — Gauging
|
95.99 | ISO/TC 1 |
ISO general-purpose metric screw threads — Gauges and gauging
|
90.93 | ISO/TC 1 |
Classification of instruments and devices for measurement and evaluation of the geometrical parameters of surface finish
|
95.99 | ISO/TC 213 |
Instruments for the measurement of surface roughness by the profile method — Vocabulary
|
95.99 | ISO/TC 213 |
Instruments for the measurement of surface roughness by the profile method — Contact (stylus) instruments of progressive profile transformation — Profile recording instruments
|
95.99 | ISO/TC 213 |
Roughness comparison specimens — Part 1: Turned, ground, bored, milled, shaped and planed
|
95.99 | ISO/TC 213 |
Roughness comparison specimens — Part 1: Turned, ground, bored, milled, shaped and planed
|
95.99 | ISO/TC 213 |
Roughness comparison specimens — Part 2: Spark-eroded, shot blasted and grit blasted, and polished
|
95.99 | ISO/TC 213 |
Roughness comparison specimens — Part 2: Spark-eroded, shot-blasted and grit-blasted, and polished
|
95.99 | ISO/TC 213 |
Roughness comparison specimens — Part 3: Cast surfaces
|
95.99 | ISO/TC 213 |
Instruments for the measurement of surface roughness by the profile method — Contact (stylus) instruments of consecutive profile transformation — Contact profile meters, system M
|
95.99 | ISO/TC 213 |
Geometrical Product Specifications (GPS) — Surface texture: Profile method — Nominal characteristics of contact (stylus) instruments
|
90.92 | ISO/TC 213 |
Geometrical Product Specifications (GPS) — Surface texture: Profile method — Nominal characteristics of contact (stylus) instruments — Technical Corrigendum 1
|
60.60 | ISO/TC 213 |
Vernier callipers reading to 0,1 and 0,05 mm
|
95.99 | ISO/TC 213 |
Micrometer callipers for external measurement
|
95.99 | ISO/TC 213 |
Geometrical product specifications (GPS) — Dimensional measuring equipment: Micrometers for external measurements — Design and metrological characteristics
|
95.99 | ISO/TC 213 |
Geometrical product specifications (GPS) — Dimensional measuring equipment — Design and metrological characteristics of micrometers for external measurements
|
60.60 | ISO/TC 213 |
Gauge blocks
|
95.99 | ISO/TC 213 |
Geometrical Product Specifications (GPS) — Length standards — Gauge blocks
|
90.93 | ISO/TC 213 |
Geometrical Product Specifications (GPS) — Length standards — Gauge blocks — Technical Corrigendum 1
|
60.60 | ISO/TC 213 |
Blanks for plug gauges and handles (taper lock and trilock) and ring gauges — Design and general dimensions
|
95.99 | ISO/TC 213 |
Geometrical product specifications (GPS) — Dimensional measuring equipment: inside micrometers — Part 1: Two-point inside micrometers — Design and metrological characteristics
|
40.60 | ISO/TC 213 |
Geometrical Product Specifications (GPS) — Surface texture: Profile method; Measurement standards — Part 1: Material measures
|
90.20 | ISO/TC 213 |
Geometrical Product Specifications (GPS) — Surface texture: Profile method; Measurement standards — Part 2: Software measurement standards
|
95.99 | ISO/TC 213 |
Geometrical Product Specifications (GPS) — Surface texture: Profile method; Measurement standards — Part 2: Software measurement standards — Technical Corrigendum 1
|
95.99 | ISO/TC 213 |
Geometrical Product Specifications (GPS) — Surface texture: Profile method; Measurement standards — Part 2: Software measurement standards — Technical Corrigendum 2
|
95.99 | ISO/TC 213 |
Geometrical product specifications (GPS) — Surface texture: Profile method; Measurement standards — Part 2: Software measurement standards
|
90.93 | ISO/TC 213 |
Geometrical product specifications (GPS) — Rotary axis form-measuring instruments — Design and metrological characteristics
|
60.00 | ISO/TC 213 |
Vernier callipers reading to 0,02 mm
|
95.99 | ISO/TC 213 |
Height setting micrometers and riser blocks
|
95.99 | ISO/TC 213 |
Building construction — Measuring instruments — Procedures for determining accuracy in use — Part 2: Measuring tapes
|
95.99 | ISO/TC 172/SC 6 |
Building construction — Measuring instruments — Procedures for determining accuracy in use — Part 7: Instruments when used for setting out
|
95.99 | ISO/TC 172/SC 6 |
Building construction — Measuring instruments — Procedures for determining accuracy in use — Part 8: Electronic distance-measuring instruments up to 150 m
|
95.99 | ISO/TC 172/SC 6 |
Building construction — Measuring instruments — Procedures for determining accuracy in use — Part 10: Difference between non-glass reflectors and electronic distance-measuring prisms (traditional glass prisms) for distances up to 150 m
|
95.99 | ISO/TC 172/SC 6 |
Surface plates — Part 1: Cast iron
|
90.93 | ISO/TC 213 |
Surface plates — Part 2: Granite
|
90.93 | ISO/TC 213 |
Geometrical product specifications (GPS) — Dimensional measuring equipment: Dial test indicators (lever type) — Design and metrological characteristics
|
90.93 | ISO/TC 213 |
Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 1: Vocabulary
|
90.93 | ISO/TC 213 |
Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 1: Vocabulary — Technical Corrigendum 1
|
60.60 | ISO/TC 213 |
Coordinate metrology — Part 2: Performance assessment of coordinate measuring machines
|
95.99 | ISO/TC 213 |
Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 2: CMMs used for measuring size
|
95.99 | ISO/TC 213 |
Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 2: CMMs used for measuring linear dimensions
|
90.93 | ISO/TC 213 |
Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 3: CMMs with the axis of a rotary table as the fourth axis
|
90.93 | ISO/TC 213 |
Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 4: CMMs used in scanning measuring mode
|
95.99 | ISO/TC 213 |
Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 4: CMMs used in scanning measuring mode — Technical Corrigendum 1
|
95.99 | ISO/TC 213 |
Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 5: CMMs using multiple-stylus probing systems
|
95.99 | ISO/TC 213 |
Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 5: CMMs using single and multiple stylus contacting probing systems
|
95.99 | ISO/TC 213 |
Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring systems (CMS) — Part 5: Coordinate measuring machines (CMMs) using single and multiple stylus contacting probing systems using discrete point and/or scanning measuring mode
|
60.60 | ISO/TC 213 |
Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 6: Estimation of errors in computing Gaussian associated features
|
90.93 | ISO/TC 213 |
Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 6: Estimation of errors in computing Gaussian associated features — Technical Corrigendum 1
|
60.60 | ISO/TC 213 |
Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 7: CMMs equipped with imaging probing systems
|
90.93 | ISO/TC 213 |
Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring systems (CMS) — Part 8: CMMs with optical distance sensors
|
90.20 | ISO/TC 213 |
Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring systems (CMS) — Part 9: CMMs with multiple probing systems
|
90.20 | ISO/TC 213 |
Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring systems (CMS) — Part 10: Laser trackers for measuring point-to-point distances
|
95.99 | ISO/TC 213 |
Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring systems (CMS) — Part 10: Laser trackers
|
60.60 | ISO/TC 213 |
Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring systems (CMS) — Part 12: Articulated arm coordinate measurement machines (CMM)
|
90.93 | ISO/TC 213 |
Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring systems (CMS) — Part 13: Optical 3D CMS
|
60.60 | ISO/TC 213 |
Geometrical Product Specifications (GPS) — Surface texture: Profile method — Calibration of contact (stylus) instruments
|
95.99 | ISO/TC 213 |
Geometrical Product Specifications (GPS) — Surface texture: Profile method — Calibration of contact (stylus) instruments — Technical Corrigendum 1
|
95.99 | ISO/TC 213 |
Geometrical product specifications (GPS) — Surface texture: Profile method — Calibration of contact (stylus) instruments
|
90.92 | ISO/TC 213 |
Geometrical product specification (GPS) — Coordinate measuring machines (CMM): Testing the performance of CMMs using single-stylus contacting probing systems
|
95.99 | ISO/TC 213 |
Geometrical product specifications (GPS) — Dimensional measuring equipment: Electronic digital-indicator gauge — Design and metrological characteristics
|
90.93 | ISO/TC 213 |
Geometrical product specifications (GPS) — Dimensional measuring equipment; Height gauges — Design and metrological characteristics
|
90.93 | ISO/TC 213 |
Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 1: Callipers; Design and metrological characteristics
|
95.99 | ISO/TC 213 |
Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 1: Design and metrological characteristics of callipers
|
90.20 | ISO/TC 213 |
Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 2: Calliper depth gauges; Design and metrological characteristics
|
95.99 | ISO/TC 213 |
Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 2: Design and metrological characteristics of calliper depth gauges
|
60.60 | ISO/TC 213 |
Geometrical product specifications (GPS) — General concepts and requirements for GPS measuring equipment
|
95.99 | ISO/TC 213 |
Geometrical product specifications (GPS) — General concepts and requirements for GPS measuring equipment — Technical Corrigendum 1
|
95.99 | ISO/TC 213 |
Geometrical product specifications (GPS) — General concepts and requirements for GPS measuring equipment
|
90.93 | ISO/TC 213 |
Geometrical product specifications (GPS) — Coordinate measuring machines (CMM): Technique for determining the uncertainty of measurement — Part 1: Overview and metrological characteristics
|
90.93 | ISO/TC 213 |
Geometrical Product Specifications (GPS) — Coordinate measuring machines (CMM): Technique for determining the uncertainty of measurement — Part 2: Part 2: Evaluating task-specific measurement uncertainty by multiple measurement strategies using a single uncalibrated workpiece
|
30.60 | ISO/TC 213 |
Geometrical product specifications (GPS) — Coordinate measuring machines (CMM): Technique for determining the uncertainty of measurement — Part 3: Use of calibrated workpieces or measurement standards
|
90.93 | ISO/TC 213 |
Geometrical Product Specifications (GPS) — Coordinate measuring machines (CMM): Technique for determining the uncertainty of measurement — Part 3: Use of calibrated workpieces or standards
|
95.99 | ISO/TC 213 |
Geometrical Product Specifications (GPS) — Coordinate measuring machines (CMM): Technique for determining the uncertainty of measurement — Part 4: Evaluating task-specific measurement uncertainty using simulation
|
90.20 | ISO/TC 213 |
Metric series wires for measuring screw threads
|
90.93 | ISO/TC 1 |
По запросу ничего не найдено. Пожалуйста, попробуйте изменить настройки фильтра.